Difference between revisions of "Multiband-antenna-for-rtk"
| Line 70: | Line 70: | ||
! style="background-color:#9b9b9b;" | Specs | ! style="background-color:#9b9b9b;" | Specs | ||
|- | |- | ||
| | | Frequency Range | ||
| | |GPS L1/L2/L5 | ||
GPS L1/L2/L5 | BDS B1/B2/B3 | ||
GLONASS G1/G2 | |||
GALILEO E1/E5a/E5b | |||
|- | |- | ||
| Bandwidth | | Bandwidth | ||
| ≥100MHz | | ≥100MHz | ||
|- | |- | ||
| | | Highest benefit | ||
| ≥4 dBic typ (@70*70 Ground) | | ≥4 dBic typ (@70*70 Ground) | ||
|- | |- | ||
| | | Standing wave ratio | ||
| ≤2.0 | | ≤2.0 | ||
|- | |- | ||
| | | Polarization mode | ||
| | | Right-hand circular polarization(RHCP) | ||
|- | |- | ||
| | | Axle ratio | ||
| ≤3 dB | | ≤3 dB | ||
|} | |} | ||
Revision as of 16:59, 6 May 2024
Multi-band antenna for RTK application
With the demands for high precision position, it increases the needs of received GNSS satellites’ number,making the trend of receiving multi-band GNSS system. Choosing a correct antenna is hugely important since antennas are the main interface between the GNSS space segment and the user, especially on multi-band system.
AGR6302G is designed for RTK applications, covering GPS, BDS, Galileo, GLONASS, IRNSS and QZSS system, details please refer to table 1. The antenna features stable signal quality and more angle receiver on the practical conditions. It employs the stack four feeds antenna architecture with hybrid to achieve the multi-band operation/ lower axial ratio/wider half power beam width and excellent right hand circular polarization.
With the newly architecture, the active part has two stages, one level filter and also one LNA for respective lower/higher band path. And then, the combiner of dual filter and the second level LNA output the RF gain to receiver. It provides excellent noise figure/ RF linear and LNA gain and out band rejection, resulting in good signal/noise ratio and anti-interference. It is housed in a compact, industrial-grade waterproof mount enclosure, the antenna can be installed almost anywhere allowing for greater flexibility. Using SMA connector fit together with GNSS module or receiver to show the dual band RTK performance.
Mechenical specs
| Items | Specs |
|---|---|
| Frequency Range | GPS L1/L2/L5
BDS B1/B2/B3 GLONASS G1/G2 GALILEO E1/E5a/E5b |
| Bandwidth | ≥100MHz |
| Highest benefit | ≥4 dBic typ (@70*70 Ground) |
| Standing wave ratio | ≤2.0 |
| Polarization mode | Right-hand circular polarization(RHCP) |
| Axle ratio | ≤3 dB |
Environmental
| Item | Specs |
|---|---|
| Temperature(Typical) | -40℃~+70℃ |
| Temperature(Max) | -40℃~+85℃ |
| Humidity | 10 to 95% RH |
Electrical performance
The electrical performance of the samples described in this document was measured under specific conditions:
- temperature: 25±15℃;
- humidity: 65±20%RH;
- instrument power setting: 1uW;
- air pressure: (0.96±0.1) X 105 Pa;
all experimental data were obtained by measuring with a block antenna connected to a grounding plate measuring 70*70mm, inside a microwave darkroom.
Antenna（Patch）Specs
| Items | Specs |
|---|---|
| Frequency Range | GPS L1/L2/L5
BDS B1/B2/B3 GLONASS G1/G2 GALILEO E1/E5a/E5b |
| Bandwidth | ≥100MHz |
| Highest benefit | ≥4 dBic typ (@70*70 Ground) |
| Standing wave ratio | ≤2.0 |
| Polarization mode | Right-hand circular polarization(RHCP) |
| Axle ratio | ≤3 dB |
低噪放（LNA）性能指标
| 参数 | 规格 | |
|---|---|---|
| 增益 | BDS B1
GPS L1 GLONASS G1 GALILEO E1 |
27.0±3dB |
| BDS B2/B3
GPS L2/L5 GLONASS G2 GALILEO E5a/E5b |
29.0±3dB | |
| 噪声系数 | 2.0 dB typ | |
| 输入驻波 | ≤2.0 | |
| 输出驻波 | ≤2.0 | |
| 电压 | DC 3.0～5.0V | |
| 电流 | ≤60mA (@3.3V) | |
| 阻抗 | 50Ω | |