Difference between revisions of "TAU951M"
| Line 253: | Line 253: | ||
'''Related Documents''' | '''Related Documents''' | ||
*[[ | *[[TAU951M_Datasheet]] | ||
*[[Satrack Quickguide]] | *[[Satrack Quickguide]] | ||
*[[Allystar_GNSS_Protocol]] | *[[Allystar_GNSS_Protocol]] | ||
Revision as of 09:37, 3 April 2024
TAU951M RTK module
The TAU951M series has two product models：
- TAU951M-P2,Standard RTK
- TAU951M-K2,Standard RTK with DR support
The TAU951M-P2 series is a set of GNSS dual-band high-precision RTK navigation and positioning module which is based on the state of art CYNOSURE IV dual-core SoC chip.
It is capable of tracking all global civil navigation systems (BDS, GPS, GLONASS, Galileo, QZSS, NavIC, and SBAS), as well as BDS-3 signals.
The latest dual-core architecture CYNOSURE IV adopts 22 nm process, with built-in dual-core MCU and 8Mbit MRAM, integrating multi-band multi-system GNSS RF and baseband.
This newly designed architecture makes the module achieve centimeter level position accuracy and higher sensitivity,greater for improved jam resistance and multipath,
and provide a highly robust service in complicated environment.
Along with its preeminent performance, the compact size (16.0×12.2×2.4 mm) of TAU951M-P2 series of LCC package with lower consumption makes it suitable for various demands
under different conditions.
It can be widely used in mower, Intelligent transportation, surveying and mapping, unmanned aerial vehicles (UAVs), intelligent agriculture, and other fields.
Features
- Concurrent reception of multi-band multi-system satellite signals
- Tracking 128 GNSS signal channels at the same time
- Support BDS-3 signals: B1C, B2a
- Support PPP-B2b/PPP/PPP-RTK (upon request)
- Internal PVT, RTD, and RTK Engine
- Update rate up to 10 Hz
- Support A-GNSS
- Smart jammer detection and suppression
| Mode | GPS/QZS | BDS | GLONASS | GALILEO | NavIC | SBAS | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| L1CA | L1C | L2C | L5 | L6 | B1I | B1C | B2I | B2b | B2a | B3I | G1 | G2 | E1 | E5a | E5b | E6 | L5 | L1 | |
| A(default) | * | (1) | - | * | - | * | * | - | - | * | - | * | - | * | * | - | - | (1) | * |
| B | * | (1) | * | - | - | * | * | * | - | - | - | * | * | * | - | * | - | - | * |
| C | * | * | * | - | - | * | * | - | - | - | - | * | - | * | - | - | - | - | * |
[1] Supported upon request with special firmware
Block diagram
Specifications
| Parameter | Specifications | ||
|---|---|---|---|
| Constellations | BDS, GPS, QZSS, GLONASS, Galileo, NavIC, SBAS | ||
| Channel | 128 | ||
| Update rates | 10Hz | ||
| Position accuracy | GNSS | 1.0m CEP | |
| SBAS | ＜1.0m CEP | ||
| RTK | 1.0 cm + 1 ppm (H) 2.0 cm + 1 ppm (V) | ||
| Velocity & Time accuracy | GNSS | 0.05 m/s CEP | |
| 1PPS | 20ns RMS | ||
| TTFF | Hot start | 1s | |
| Cold start | 27s | ||
| RTK | Convergence time | <10s | |
| Reliability | ＞99.9% | ||
| Sensitivity[1] | Cold start | -148 dBm | |
| Hot start | -155 dBm | ||
| Reacquisition | -158 dBm | ||
| Tracking & navigation | -165 dBm | ||
| Protocol | NMEA-0183 | ||
| RTCM 2.X, RTCM 3.X | |||
| Baudrate | 115200 bps, by default | ||
| Operating condition | Main supply | 1.75V to 3.63V | |
| Digital I/O supply | 1.75V to 3.63V | ||
| Backup supply | 1.62V to 3.63V | ||
| Power consumption | Tracking | GNSS | 30 mA @ 3.3V |
| Single system | 18 mA @ 3.3V | ||
| Standby | Data backup | 16 uA | |
| RTC | 1.4 uA | ||
| Serial interface | UART | 2 | |
| SPI[2] | 1 | ||
| I2C[2] | 1 | ||
| Operating limit | Velocity | 515 m/s | |
| Altitude | 18,000m | ||
| Environmental conditions | Operating temp. | -40°C to +85°C | |
| Storage temp. | -40°C to +90°C | ||
| Humidity | 95% RH | ||
| Size | 16.0×12.2×2.4 mm, 24pin LCC | ||
[1] tested with a good external LNA
[2] Supported upon request with special firmware
Related Documents